1025R Sub-Compact Utility Tractor
- John Deere
- Compact Utility Tractors 1 Family
Find a location to get your local store information and inventory.
Find Location
Key Features & Specs
- Powerful Tier 4-compliant diesel engine
- New, easy-lift hood with dual gas-charged lift struts
- Premium Operator Station with ergonomic seat, armrests and fender lights
- Auto-Connect™ mid-mower deck can be installed or removed in less than 5 minutes
- HP 23.9*
- PTO HP 18
- Transmission Type Hydrostatic - 2 Range
- 2WD or 4WD 4WD
- 3PT Hitch Category 1

- + Expand All
- - Close All
-
Implement compounding improves efficiency
Implement compounding (1025R Tractor shown)
- Allows mounting more than one implement at a time, eliminating implement changeover
- Loader, mid mower, backhoe, and a variety of 3-point hitch implements can be attached to the tractor at the same time
-
Easy-open, gas-lift hood
Gas-lift spring
- The under-hood gas-lift support provides easy one-finger access to the engine compartment and eliminates the need for a mechanical prop rod.
- This design of the support structure provides excellent rigidity for the hood.
-
Hydrostatic transmission (HST) with Twin Touch™ foot controls
The 1023E and 1025R Tractors feature a HST.
- Fluid under pressure transmits engine power to the drive wheels through a hydraulic pump and motor
- The hydrostatic-drive unit functions both as a clutch and transmission
Twin Touch foot controls
Twin Touch foot controls allow selecting both speed and direction of travel with a touch of the toe. Ideally suited for jobs where productivity is a must, such as loader or mower applications.
- Infinite ground speeds, even at full throttle, to match the job
- No clutching for fast direction changes
- Faster, easier, and more precise to operate than competitive tractors with treadle pedal design (toe-heel)
- Provides high torque for start up
- Reduces power train shock loads
- Large foot pedals were designed for operator comfort and allow for convenient operation of the tractor
Two-speed transmission
Transmission has two speeds - Hi and Lo range.
- The range lever is located next to the seat, conveniently within reach of the operator
- Lo range allows performing tougher tasks at higher speeds than competitive tractors equipped with a three-range transmission (that is, lo range on three-speed transaxle is slower than lo range on a two-speed transaxle)
Durability features include:
- Large forged one-piece trunnion shaft with larger support bearings that reduce vibration and noise.
- Innovative transaxle combines an HST, gear reduction axle, and clutch.
- Pressure side filtration allows using a finer-mesh filter (10 micron) than suction filtration systems use on many competitive tractors.
- One pump to supply charge pressure and implement flow. A flow divider splits the flow to various circuits throughout the tractor.
- The transaxle has an oil cooler which provides improved hydraulic cooling performance.
-
Optional cab offers protection from elements
The field-installed cab offers protection from the elements and expands the versatility of 1025R Tractors to perform in all climates.
1025R Cab – LP68087
Key features:
- Full glass doors for maximum visibility
- Curved glass for a styled look
- Sealed for cold weather operation
- Easily removable for summer operation
- Heater with fan
- Switches and vents integrated into headliner
- Dome light
- Fully openable front and rear windows with gas struts
- Front sun visor
- Front work lights
- Front wiper with washer system
- Dual outside mirrors
- Rollover protective structure (ROPS) certified cab frame
- Allows for improved rear visibility
- Reduces overall height
- Rubber isolation at all mounting points
- Interior sound insulation
- Immersion-primed and powder-coated cab frame
- Provides superior corrosion resistance
- Integrated John Deere styling
Specifications:
- Cab height: 1525 mm (60 in.)
- Overall height when installed: 1990 mm (78.4 in.)
- Overall height when installed to top of beacon: 2159 mm (85 in.)
- Overall width with cab installed: same as tractor width
- Cab weight: 200 kg (440 lb)
Optional kits:
- Rear wiper kit – LP68115
- Stereo kit – LP68120
- Beacon light kit – LP68116
- Light-emitting diode (LED) rear work light kit – LP68117
- Illuminated license plate kit – LP68118
- Retro-fit kit – LP68119
- Required for all 1026R Tractors. Also required for 1025R Tractors built prior to calendar year 2016. Calendar year 2016 machines will have a G in the 10th position of the serial number.
- NOTE: Any tractor that does not have the gas-lift struts on the hood will require this retro-fit kit.
Compatibility and Installation:
- Compatible with:
- 1025R
- 1026R
- Not compatible with:
- 1023E
- 1025R TLB (FILB)
- 1026R TLB (FILB)
- Compatible with all tractor implements except 260 Backhoe.
- Cabs will be shipped direct to the dealership and installed by a service technician.
- Estimated installation time is 7-8 hours.
- Full glass doors for maximum visibility
-
Powerful Tier 4-compliant diesel engine and standard dual mid-selective control valve (SCV)
Powerful engine
- Tier-4-compliant isolated Yanmar® TNV clean and silent diesel engine
- 24.2 gross hp (PS) - 18.0 power take-off (PTO) hp
- 3200 rpm rated speed
Strong hydraulics
- Standard dual mid-selective control valve (SCV) with integrated loader joystick
- Third-SCV kit
- Power-beyond kit
- Independent hydraulic-lift kit
Comfortable operator station and controls
- Ag tractor family styling with sloping hood design
- Folding rollover protective structure (ROPS)
- Deluxe-suspension seat with armrests
- Standard cruise control
- Tilt steering
- Standard tool box
- 12-V outlet
- Ergonomic-floor mat
- Cup holder
- Standard side fender lights
Versatile implements
- D120 and H120 Loaders
- 54D AutoConnect™ and 60D AutoConnect 7-Iron™ mower decks
- Material-collection system
- 260 Backhoe
- iMatch™ AutoHitch™
- Rotary brooms 132.1 cm and 152.4 cm (52 in. and 60 in.)
- Front blade 137.2 cm (54 in.)
- Snow blowers 119.4 cm and 137.2 cm (47 in. and 54 in.)
- Rotary tillers (647)
Yanmar is a U.S.-registered trademark of Yanmar Company Limited.
-
Fast and easy implement changeover
- Front Quik-Tatch™ hitch makes changing front implements quick and easy
- All front implements (blade, brooms, and snow blowers) use a common hitch
- AutoConnect™ mid-mount mower decks, D120 and H120 Loaders, and 260 Backhoe can be taken on or off within 5 minutes, and no tools are necessary
- Changing rear implements is a snap with the iMatchTM Quick-Hitch, which has three fixed points to back in and pick up a rear implement that is iMatch compatible
*Features shown are available with all current model year tractors.
-
Easy operation four-wheel drive (4WD) power steering
Both 4WD and power steering are standard equipment on the 1025R. This combination allows for excellent maneuverability and ease of operation of the tractor.
- Narrow overall width allows the 1025R to work in tight areas where most compact tractors just cannot fit, yet the 144.8-cm (57-in.) wheel base and 119.4 cm (47 in.) overall width gives great stability for all type of terrains.
- Power steering means fewer turns of the steering wheel than manual steering; especially valuable when mowing around obstacles or when the tractor is used with a front loader.
- High horsepower-to-weight ratio makes the 1025R a good choice for a variety of tasks; overall tractor weight reduces ground compaction and makes the 1025R an excellent mowing tractor.
- The power take-off (PTO) is a fully-independent PTO on the 1025R, allowing engaging and disengaging of the PTO without stopping tractor movement. This is important when driving across obstacles such as driveways while mowing.
-
Optional iMatch™ Quick-Hitch feature allows for easy implement hookup
iMatch Quick-Hitch
iMatch Quick-Hitch with rotary cutter hookup
iMatch Quick-Hitch (LVB25976)
iMatch Quick-Hitch with rotary cutter hookup (LVB25976)
One of the greatest operator concerns involves difficulty in attaching tractor implements. John Deere has addressed this issue with the iMatch Quick-Hitch.
The iMatch Quick-Hitch provides easy hookup and a guaranteed fit for all Category 1 implements that are designed to meet the American Society of Agricultural and Biological Engineers (ASABE) Category 1 Standard S278.6 for quick-attach hitches.
- All implements require a set of bushings in order for the attachment to fit and work properly with the iMatch Quick-Hitch. One set of bushings comes with the iMatch Quick-Hitch.
NOTE: The bushing set can be seen in the picture above. These bushings allow the hooks on the iMatch and the pins on the implement to fit together properly. All other implements (box blades, tillers, rear blades, etc.) will require a set of bushings to enlarge the pin to fit with the iMatch hooks. Bushings of different lengths can be found in the parts system or through a bushing supplier (see dimensions below).
- Upper bushing
- Inside diameter: 1.93-1.95 cm (0.76-0.77 in.)
- Outside diameter: 3.15-3.18 cm (1.24-1.25 in.)
- Lower bushings
- Inside diameter: 2.24-2.26 cm (0.88 to 0.89 in.)
- Outside diameter: 3.63-3.66 cm (1.43 to 1.44 in.)
-
Open operator's station is comfortable and convenient
Open operator's station
The 1025R operator's station has been designed to allow greater operator comfort and increased visibility. Large and easy to grab handrails are located on each fender for an easier on and off of the tractor from either side.
- Sloping hood design provides improved visibility
- Operator's station provides plenty of room for comfortable operation
- Step-through textured flat operator station makes getting on and off the tractor easy from either side of the tractor
- Fender-mounted handrails are large and easy to grab; located on each fender, they assist the operator in getting on and off the tractor
- Controls are located next to the fenders for operator convenience
- Operator controls are color-coded for easy identification of operation
- Front-horizontal exhaust for increased operator visibility
*Features shown are available with all current model year tractors.
Operator presence system
- If the operator leaves the tractor seat when the transmission, mid or rear power take-off (PTO) is engaged, the engine will shut down
Foldable Roll-Gard ROPS
Foldable Roll-Gard™ rollover protective structure (ROPS) and retractable-seat belt are standard equipment to protect the operator in the event of a tractor tip-over, as well as improve the ability to store tractor in a garage.
Seat belt is within easy reach of the operator, to encourage the use of it whenever operating the tractor.
*Features shown are available with all current model year tractors
Lighting
Standard (and optional) lighting shown
Standard equipment lighting includes:
- Two front-mounted sealed-beam halogen headlights
- Two amber-flashing warning/hazard lights mounted on the side of the ROPS with reflectors
- Two additional fender lights are standard on the 1025R
- Additional front- and rear-light kits are available
*Features shown are available with all current model year tractors
-
Mower deck lift components
1025R Tractor
- The 1 Family tractors includes factory-installed mechanical deck lift components.
- The addition of these components from the factory significantly reduces the time required to do the initial mower deck installation at the time of purchase.
- Refer to the mowers and material collection page for more details on mower deck installation and compatibility.
3-point hitch
Lift capacity, 24-in. behind link arms | 309 kg 681 lb |
Type | Limited Category 1 |
Cab
Compliance | NA |
Visibility | NA |
Air conditioning, temperature differential | NA |
Doors | NA |
Noise rating | NA |
Seat equipment | NA |
Dimensions
Wheelbase | 145 cm 57.1 in. |
Front axle clearance | 195 mm 7.7 in. |
Turning radius without brakes | 2.25 m 7.4 ft |
Limited slip differential | No |
Approximate shipping weight (open-station; cab) | 655 kg 1444 lb |
Electrical
Battery size | 500 CCA |
Alternator (12-V) | 40 amp |
Starter size | 1.2 kW 1.6 hp |
Engine
Family | EYDXL1.27NS1 FYDXL1.27NS1 GYDXL1.27NS1 |
Manufacturer | Yanmar |
Engine model | 3TNV80F-NCJT |
Engine power (gross) | 17.8 kW 23.9 hp 24.2 PS SAE J1995 rated power |
Power take-off (PTO) power | 13.4 kW 18 hp |
Rated engine speed | 3200 rpm |
Type | Diesel |
Injection pump type | Indirect Injection |
Aspiration | Natural |
Emissions compliance | Final Tier 4 |
Cylinders/displacement | 3 / 1.267 L 3 / 77.3 cu in. |
Number of cylinders | Three |
Cylinder liners | Cast-in-block |
Bore and stroke | 80x84 mm 3.15x3.31 in. |
Compression ratio | 23.0:1 |
Lubrication | Pressurized |
Cooling system | Water pump |
Air cleaner | Dual element with mechanical restriction indicator |
Engine torque at rated speed | 55.2 Nm 40.7 lb-ft |
Fuel tank capacity | 21.2 L 5.6 U.S. gal. |
Final drive
Type | Bull Gear |
Differential lock | Yes |
Fluid capacities
Crankcase with filter | 2.7 L 2.9 qt |
Transmission and hydraulic system | 3.7 gal. 14 L |
Fuel system
Type | Indirect Injection |
Fuel consumption | 5.8 L/hr 1.5 U.S. gal./hr |
Hydraulics
Type | Open center |
Pump type | Gear |
Maximum operating pressure | 137.9 bar 2000 psi |
Draft control sensing | Position control |
Remote control valves available | Two |
Pump rated output | Steering 13.2 L/min 3.5 gpm Implement 13.2 L/min 3.5 gpm 24 L/min 6.3 gpm |
Key Specs
Steering hydraulics | 13.2 L/min 3.5 gpm |
Implement hydraulics | 13.2 L/min 3.5 gpm |
Hitch type | Limited Category 1 |
Engine power (gross) | 17.8 kW 23.9 hp 24.2 PS SAE J1995 rated power |
Standard transmission; forward/reverse | Hydrostatic - 2 range |
Approximate shipping weight (open-station; cab) | 655 kg 1444 lb |
Wheelbase | 145 cm 57.1 in. |
Cruise control | Standard |
Lift capacity, 24-in. behind link arms | 309 kg 681 lb |
Power take-off (PTO) power | 13.4 kW 18 hp |
Miscellaneous
Toolbox | Yes |
Operator station
Rollover protective structure | Type Foldable Yes |
Platform - flat/straddle | One-piece semi flat |
Gear shift location - console/floor | Left-hand side |
Power take-off (PTO)
Standard | Rear - 540 rpm Mid - 2100 rpm |
Control | Independent |
Clutch | Wet disc |
Brake (for mid and rear PTO) | Wet disc |
Tires
Front | R4 - 18x8.5-10 |
Rear | R4 - 26x12-12 |
Front tread range | 91.8 cm 36.1 in. |
Transmission
Standard transmission; forward/reverse | Hydrostatic - 2 range |
Left-hand reverser | No |
Final drive | Bull Gear |
Brakes | Wet disc (left-hand pedal) |
Steering | Power |
Clutch, wet/dry | N/A |
Creeper | No |
Cruise control | Standard |
Differential lock | Yes |
Axle capacity | Front 612 kg 1349 lb Rear 715 kg 1576 lb |
4.48
A workhorse
I bought my 1025R in March of 2016 with a H120 loader, a 5' rear blade, and have since added the quick change pallet forks (not the clamp on type). I have only .75 acre but care for my home myself. Having had 2 back operations and 2 titanium slugs placed on the upper and lower spine, I needed to avoid lifting, stooping down, twisting, and generally stressing the back which is the sole purpose for buying the machine. I have 34 hours on the machine now without a single problem. Trimming shrubbery standing up and placing them in the loader bucket or on the pallet forks at waste height is a blessing. I used it to dig irrigation pipe ditch and cover it back up. I carry trimmings to a yard waste and simply raise the bucket and dump it. No bins, no cutting to length, no raking, no shoveling. My back loves it. Lifted and installed a gun safe with no problem. Carried concrete pavers, loaded and unloaded pine bark mulch. Great machine. I should have gone one size bigger but the 1025R is a great machine.
BackSaver
- From: Seven Lakes, NC, USA
- Usage Frequency: Weekly
- Level of Experience: Intermediate
Does everything well
I bought TLB, Love it!! I added 9 iron finish mow deck, 48" Shredder and 48" Box blade. I have 5 acers, 1/2 mile dirt drive way. This unit works great, easy to use. I love the hydro trans and driver over finish mow deck. Very fast to swap out attachments. I'm very surprised the power this unit had for its size. This is a unit you will keep for years. Having this 1025r for over a year and 300 hours on it, I have to say, my John Deere starts and runs like new, Does not leak a drop, I do take good care of but I do keep out side all the time. All I do is keep oil changed (with maintenance agreement) and keep sprayed off. Very good unit, Bach hoe attachment more useful than I though I would ever use.
SusieQ
- From: Buffalo Gap, TX 79508, USA
- Usage Frequency: Daily
- Level of Experience: Intermediate
Our 1025R is a great work horse with plenty of power
We bought our 1025r to mow the 4 acres of rough grass which it handles with ease. We used the front loader to plow, push and lift lot's of snow this past winter and she never hesitated lifting or pushing even up a 3 degree grade. The back hoe may be small but it works just like the big ones and is very good at digging up tree roots and digging holes. Frankly, 90% of the use on our 1025r has been removing tree roots, and clearing out saplings and small trees up to 6" diameters. We've leveled and graded our grounds and moved 15 tons of decorative marble stone chips without any issues. Bottom line, we love our John Deere 1025r
PeterD
- From: Connecticut
- Usage Frequency: Weekly
- Level of Experience: Beginner
Avery useful little powerhouse.
I have had this machine since July 2015 & have about 25 hours on it. In addition to the FILB I have a 47" front Snow Blower & a Box Ballast on the back. I also have the 54" drive over belly mower. Although it does take some practice the implements are very easy to change out. The caveats are to always change & store implements on firm level surface & to relieve hydraulic pressure on the lines before removing the lines: very important! That having been said everything about this machine is as advertised. It is a real powerhouse! Wish I got it at least a year sooner! I have moved tons of gravel & dirt. I have dug numerous holes of varying depth & width & I had a brief chance at snow blowing. A great little machine.
Joe1
- From: Highland, NY
- Usage Frequency: Weekly
- Level of Experience: Beginner
AMAZING!!
Great little work horse. I have a box blade,60in mower, fertilizer spreader and loader and use it daily. Highly recommend
Joey
- From: IA
- Usage Frequency: Daily
- Level of Experience: Intermediate
One awesome tractor
Now two weeks post adoption of my newest green family member! Solidly built, such thorough safety features I am comfortable starting training (with supervision!) of my two daughters. One tip: if you order with forward field lights (mounted to the hazard light guards) ALSO order rear field lights at same! Due to the requisite mounting point (due to folding ROPS) I find the light in my face if working at night when I turn to back up- and all behind becomes invisible! Be safe and light yourself all the way around... Looking forward to many green years ahead!
Dieseldoghouse
- From: Lakeville, MA
- Usage Frequency: Weekly
- Level of Experience: Intermediate
A great small tractor
I have about 70 hours on my 1025R. I initially bought it with the H120 loader and a Frontier rotary mower, and a rear ballast bucket for use with the loader outside of mowing season. As a first-time tractor owner, I found the 1025R was very easy to learn and use. It has plenty of power to dig and move dirt, and mowing 7-10 acres of prairie grass and brush was very easy and not too uncomfortable (aside from bumpy ground and dust, which has nothing to do with the tractor). After using it for a year, I got the I-Match quick connect hitch, and a hydraulic snow plow blade for the front. For my needs, this tractor and the implements mentioned cover everything very nicely. I have had absolutely no problems with the equipment. With the I-Match rear hitch, H120 loader, and the quick hitch snow plow blade, it literally only takes a few minutes to change implements, which is VERY nice - saves a lot of time and gets the chores done faster. I highly recommend this tractor for anyone who has a small farm/ranch or a big yard. It's a very dependable workhorse. Another bonus - 5 gallons of diesel goes a long way in this tractor. It's very cheap to operate.
ChrisV
- From: Colorado, USA
- Usage Frequency: Weekly
- Level of Experience: Intermediate
Would I purchase again? No.
I can say this unit is a little work horse, when it runs. I have own mine for almost a year now and put nearly 200 hours on it. First week I had a hydraulic leak developed on the loader. Dealership honor the warranty and fixed it. After that it was in and out of the shop because the hydrostat transmission keep creeping. After the 3rd time the plunger assembly that hold the petals in place came loose and the tractor took off down a steep hill. Scared me but luckily the brake were able to stop the tractor under full power. I ended up taking the unit to the dealership 2 more times for this issue before fixing it myself. ( I replaced the LVA17758 and used lock tight on the treads.) At 130 hours on the tractor, a backhoe hose busted that runs in between the main boom. They charge 140 dollars to repair it and also stated, "Wearable Items are not covered under the 2000 hour warranty". Eventually, this escalated to a general manager and was taken care of. Now For the big one. I was bushing hog a field when the tractor completely stopped moving. I turned the unit off and looked underneath it. There was hydraulic oil everywhere. The filter for the transmission was missing and it turns out that the nipple that holds the filter on broke off. This is part of the Cast Aluminum housing, so the transmission casing has to be replaced. Dealership Quoted 3300 dollars for repairs. John Deere really needs to relocate this or change their design to protect this part of the casing. Tip: cycle your glow plugs twice to keep the unit for filling your garage up with black smoke, even if its 95F outside it always sputters during the initial start.
Robert352
- From: Gainesville,Fl
- Usage Frequency: Daily
- Level of Experience: Expert
Tough Machine
To everyone , While waiting on my new 1025r TLB My sales girl Kylan sent me demo to start my project removing a old paver patio concrete side walks tree stumps it is amazing the power and strength this thing has easy to operate. I got my new one today and the improvements are even better. it now has the curved loader bars on the backhoe the hoes are tucked in to the frame fuel filler cap is now lined with steel threads , the back hoe has it's own seat no more swinging the seat around. GO JOHN DEER!!!!!! Could not be happier with my dealer. JD equipment in Marion OH.
ezze
- From: ohio
- Usage Frequency: Daily
- Level of Experience: Intermediate
Glad I did it
I debated for a few months whether to buy a new tractor. Some told me the competition was better, but I had to look at the John Deere as I Always had a JD. Sure am glad I bought the JD ,wish I would have done it sooner. The 60 inch deck works fine, if your looking for fine grooming, this might not be for you, but makes me happy. Everyone has a opinion, and I am happy with what it does for me.The front loader works great also, and the tractor it self has plenty of power. Glad I did it, Glad I bought the John Deere.
JFKO
- Usage Frequency: Weekly
- Level of Experience: Intermediate
This is one tough little tractor
I have 50 hrs on my 1025 with a front end loader and ballast box. I use it to clear heavy snow from my steep 150 ft driveway. It performs flawlessly so far. Great capacity on the loader lifting heavy snow for hrs. the ergonomics/controls are the best including the lights which give great field of vision at nite. These may seem like little things but believe me they are not.. The engine is more powerful than I anticipated even when pushed to the limits. fires up fast even in cold weather. The cadillac of sub compact Tractors. Go green
Canuck
1025 TLB FANTASTIC PRODUCT!!
Bought a new 1025TLB from my dealer here in Princeton. It definitely has great power and the hydraulics are incredible strong! I am already on my 5th stump and what a ball to operate! Wish I would have purchased it long ago! I also added the Barracuda thumb--excellent addition. Cost was only $330 and really helps with stumps and brush piles. Also bought the 54 inch snow blower for front. Because the FEL is so easy to remove, it makes the snow blower attachment process easy. Now just waiting for our first snow. I HIGHLY recommend this to anyone. The product development folks have really gotten this model right--Congrats JD!
captain
- From: Princeton, NJ, USA
- Usage Frequency: Weekly
- Level of Experience: Beginner
Little John needs a big brother
I have owned the 1025R for 3 years with 290 hours of use. Equipped with a front end loader (a must have) a 60 in belly mower and box blade. Have had a couple maintenance issues like leaking fuel line and neutral sensor problem which kept me from starting it. Mow quality is fair on flat ground and so so on a slope. It is a lot faster/more powerful than my JD X380. I live on 5 acres in south Alabama with LOTS of trees and vines with which to deal. Little John does pretty well, but I am going to upgrade to a 2032R for more weight/width/ capacity. Will feel much more secure on a bigger, wider tractor. Still have lots of trees with which to deal from Michael. Have a level lot? 1025 is a fine little tractor.
Bamageezer
- From: LA...Lower Alabama
- Usage Frequency: Weekly
- Level of Experience: Expert
John Deere 1025R FILB
I looked at the competitions sub compact tractor offerings before I decided on buying the John Deere . Any of them will most likely be able to do the work you have in mind. Some are boasting running at low Rpm's or doing this or that better. Here is what I have learned after sitting on the competition machines. Hands down the John Deere has controls that are easier to use. Everything from the 4x4 shifter to the loader control is within easy reach. Having been able to operate the competitions machines in real world work conditions the John Deere offers better comfort, less complex control's and is a easy machine to operate. It will do the job just as easy as a bigger machine just takes a few extra buckets.
Spider37
- From: Sutton, WV, USA
- Usage Frequency: Daily
- Level of Experience: Expert
Quick connect deck and bucket are engineering marvels
Purchased 1025r early summer 2015, mowing about 5 acres twice a week all summer. tractor has been awesome performer, no issues whatsoever. Talked to my salesmen about the height cut of my deck, they were out the next day to adjust, thanks Z and M ag and turf. My only complaint is the pto switch when backing as machine will stall if you go to reverse before pulling switch...
Tileman1
- From: Lockport, NY 14094, USA
- Level of Experience: Expert
Love my tractor!
I have had my John Deere 1025r tractor over 2 years with a 110 hrs of use and can say I am very happy with this machine. Its very simple to operate and cutting the grass up tight around trees is easy due to a very tight turning radius and precise hydro-static foot controls even with a 60" deck. I mostly use it for cutting grass but the tractors real power become apparent when you use the front loader. I have wooded area in my yard with a lot of brush and wild grape vines. Using the front loader its incredibly easy push all the brush and small trees out of the way without any manual labor. Its a lot of fun to use. Drive over deck auto connect and drive up loader attachment are easy to use and time savers. I love my John Deere.
Steve5917
- From: Sanborn, NY
- Usage Frequency: Weekly
- Level of Experience: Intermediate
1025r Working beast
I have run my 1025r for 55 hours since Jan 2015. I bought 54 inch snow thrower, 60 inch mmm, FEL, backhoe, and weight box. Non-JD clamp on forks and subsoiler too. I have 6 acres, 2 lawn, 4 woods. I down sized from a larger 36 hp tractor and consolidated 3 machines. The snow blower was timely with record snow in Boston. It went through more than 2' no problem. 11 hrs blowing in half time as before. I put in 15 hrs mowing, half time as before. I moved 20 trees of brush with forks. Moved 50 tree lengths 8-12' with forks. I pulled 1-3000 lb logs with cable out of swamp. I moved yards of manure, graded, subsoiled 25'x50' garden. I used forks and long pallet to lift material to barn loft. I dug up 6 stumps 12-20" diameter and planted 12 trees and bushes. I pulled 6 cords firewood up ice and snow path, uphill 300' to house all winter, no problem. Implement change is a breeze. Think this is not enough machine? Think again.
Jbgoody
- From: Chepachet, Glocester, RI, USA
- Usage Frequency: Weekly
- Level of Experience: Expert
mower deck
I have owned a 1025 R for 4 years now. It has a 54" quick attach deck on it. No matter what I do to the deck it will not mow without leaving an uncut strip of grass. I have done everything the manual, the JD shop people tell me to do but NOTHING will work. It leaves a strip on both sides of the mower deck no matter how high or low I cut. I have talked to two other people that have the same problem with their decks. Other than this it is the best JD product I have ever owned from a 2355 tractor to a 7810 tractor. This may seem like an easy problem to fix but there are three of us with the same issue. Any suggestions?
David
- From: Kentucky, USA
- Usage Frequency: Weekly
- Level of Experience: Expert
I won't be able to get away from this machine quick enough. Complete buyers remorse.
I bought the 1025R in April of 2015 and had nothing but trouble with the thing since. Got the machine home from the dealer and immediately, the mower deck would not connect properly. Dealer came out and took it to the shop for repairs. Got the machine back and again, something else went wrong. The dealership had the machine for over a month. We made our first payment and the machine was still in the shop. When we did get the machine back, it was a royal pain to get the deck to marry up with the mower.We finally did and I won't remove the mower deck again. I had the machine out yesterday, and the bracket that holds the seat in place broke. I'm not a very big guy by the way. It's been one headache after another with this machine. I wish I had never laid eyes on this thing. Do yourself a favor, don't even entertain the idea of buying a piece of trash like the 1025R. John Deere needs to recall this model.
Paul2764
- From: Smithville, Mo.
- Usage Frequency: Weekly
- Level of Experience: Intermediate
Love the Ergonomics!
There's more comfort in this little tractor than a nap on grandma's lap! Everything is logically laid out and functionally located. Visibility is great and getting on and off either side is a breeze. The tilt wheel makes all the difference in the world. Getting in and out of the loader and mower is a fast, easy and convenient.! You'll love the long list of attachments for this tractor. The 1025 R really is a dandy little tractor.
JD77
- From: Dryden, MI 48428, USA
- Usage Frequency: Weekly
- Level of Experience: Expert
Pleasantly surprised
Our new 1025R was delivered this morning and I immediately began giving a serious workout using the front loader and the tiller. This tractor is all we will ever need! We love it and how simple it is to operate and the available power it renders is more than I expected!!
Levi46
- From: Kansas
- Usage Frequency: Weekly
- Level of Experience: Intermediate
Best of the best
I bought the 1025R, mid mount mower with bagger, bucket, pallet forks, block heater, extra lights/light guards and hydraulic snow plow. Wish I would have looked at the ZM industries 960 snow pusher instead of the snow plow. Although I haven't used the plow yet, however the pusher might be more useful. The machine is very powerful and runs super. Z&M ag and turf (Falconer)are the best. Rod Ruttenbur knows his stuff. I shopped the Kubota. However I found the controls to look and feel cheap. The hydraulic control handle is huge. Also, the quick attach bucket, and mower deck on the Deere is tons easier on and off. (I tried both out) Don't get fooled by the sales pitch. "Kubota has steel hood and fenders" It rattles more compared to the Deere. Also the plastic doesn't rust and rattle. If you are going to spend the money, the Deere is close in price. And Deere service is tons better if you need it.
Jake2
- From: Russell, PA
- Usage Frequency: Weekly
- Level of Experience: Intermediate
Great Power and 4 wheel drive!
iv'e owned this tractor for almost a year and so far it has exceeded all my exceptations. i really fell in love with the 4 wheel drive and you can about go anywhere! the loader was also a highlight and has a lot of streigth.
tractorcarl
- From: Ripley, OH 45167, USA
- Usage Frequency: Daily
- Level of Experience: Intermediate
Versatility through attachability!
Need a small tractor for a lot of different jobs? If so the JD 1025R was made to order! Mowing, digging, lifting this tractor does it all. If attachability is key to your purchase decision you'll love this machine. I now have 135 hours on my 1025R and cannot say enough good about this tractor. I mow, landscape, handle material, plow and more and this machine gets her done. In addition, to have a Yanmar diesel is to love one. You"ll be hard-pressed to find anything more fuel efficient. Just compare the ease and convenience of implement attachment to others and you'll fall in love.
OhhowIluvmyDeere
- From: Lapeer, MI 48446, USA
- Usage Frequency: Weekly
- Level of Experience: Expert
John Deere compact 1025R , carryover- NEW model year 2016
I bought this Compact 1025R not because it was cheap >$20k! It was because it was advertised as being very diversified with an auto detached mowing deck , quick attach loader, box blade and snow blower accessories. After operating this tractor for a period of time I found that all of these features advertised with Auto disconnects require near perfect conditions for them to all attach / detach without extra efforts or adjustments. After owning my tractor for one month I decided to detach the mowing deck, when reattaching the mower deck it would not reconnect. I found that the drive shaft assembly linkages we're done in correctly at the John Deere dealership and the service techs did not pay attention to details when installing this assembly so the tractor had to go back to the shop for two days for that correction. Then on month number four I noticed anti-freeze on the floor in my shop. Upon further inspection I found the water pump front shaft seal was leaking! The tractor only has 47 hours on it. Next, I'm finding when the weather is below zero this unit gels up very easily… I've owned diesel tractors before and I have never had gelling issues as this unit seems to have a lot of idiosyncrasies.. I am now waiting for the John Deere dealership shop to pick it up again to put in a new water pump! At this time I'm not too impressed with the level of quality and workmanship coming from John Deere. In closing, this tractor is very expensive and it should not be breaking down with less than 50hrs on it! I hope John Deere improves its workmanship and pays more attention to quality and to all the necessary details in the future construction of these compact tractors as this unit is very frustrating to deal with being brand new. Thanks
Harry25
- From: Fargo, ND, USA
- Usage Frequency: Weekly
- Level of Experience: Expert
EASE OF OPERATION, GREAT ENTRY LEVEL TRACTOR
PERFECT FOR OUR LANDSCAPE OPERATION WHERE A COMPACT TRACTOR IS TOO LARGE. STILL HAS ADEQUATE POWER TO PERFORM TASKS NEEDED
BRADS1025R
- From: Central Illinois, IL, USA
- Usage Frequency: Daily
- Level of Experience: Expert
Mighty Mouse
This little tractor is deceiving, as it is really powerful and super easy to maneuver. We purchased the loader and mower deck, and added some lights. We debated a while if we needed a 4 wheel drive vs just a mower. Really glad we went this route. More then enough power for this machine.
Dan88
- From: Hedgesville, WV, USA
- Usage Frequency: Weekly
- Level of Experience: Expert
AN AWESOME MACHINE!!!
I bought mine in March of 2016. I have a little over 50 hours on it and it has been worth it's weight in gold. If you are thinking of getting one go get it. You will not be sorry! It is awesome!!! I use mine for mowing, hauling and working in the garden. Also, I highly recommend the 4' tiller. It's hard to believe how good of a job it does. Honestly I can't think of one negative thing about it. I would give it 10 stars if I could and I recommend it 1,000%
Darren46
- Usage Frequency: Weekly
- Level of Experience: Intermediate
Poor engine choice
I have owned this tractor now for 1.5 years and while it has done everything I have asked of it and can't complain of the actual build quality of the tractor itself, the yanmar diesel is not up to the standards of the rest of the tractor. First off this engine spits and sputters terribly when u first crank up from a cold start bellowing white smoke like crazy for about 30 seconds then the engine smoothes out and runs fine. Second thing is at 55 hours the engine starts choking down with rpm's in the 2700 -3000 range while pulling a load such as a 4ft disc or small middle buster plow. Dealer where I bought it has had tractor over 3 weeks and evidentially cannot fix it because every time I call to check the service mgr States he's not real sure what the tech. Has found wrong with it. This my first and last Deere product, buyers regret. Should have bought a tried and true orange tractor like several friends recommended! Seems like i was sold on marketing hype rather than quality as almost every part on this tractor is foreign made. Hope this helps.
smittydawg46
- From: Columbus, MS, USA
- Usage Frequency: Weekly
- Level of Experience: Intermediate
Hydraulic hose and snap ring in two months.
I purchased two months ago and have put over 45 hours on this tractor, I have the back hoe and the H120 loader. This is a very strong machine and I have been impressed. Its very easy to use. My concern is that the quality is not the same as my 30 year old 325 lawn mower which is tough as nails. Up on delivery the tractor had a leaking hydraulic hose that had to be replaced, I was using my new tiller, well my wife was using my new tiller and the snap ring that keeps the spline shaft on for the draft arms broke ( and that was a tough self fix ) and now the attachment lift and lower arm wont stay up....... Will this tractor make it 30 years?
DEMM
- From: Buckhannon, WV 26201, USA
- Usage Frequency: Weekly
- Level of Experience: Intermediate
Very Pleased So Far!
I did a lot of research comparing the 1025R to the competition before I made my purchase, and I am so glad I went with John Deere! I have now owned my 1025R for about 3 months and it has lived up to and exceeded my expectations. I bought the loader and 54 inch mower deck and have been very please with how both of them have performed. We have a small farm and raise chickens and turkeys and raise vegetables for the farmers market and this tractor has cut my work time in half! I had debated on getting a larger tractor and a zero turn mower separately, but I am very glad I decided to go with this set up. This tractor has a very tight turn radius in 2WD and is great for mowing even in tight spots, which I was worried about. The drive over mower does a great job cutting our 3 acres of grass, and has cut my mowing time in half of what my old Craftsman mower could do it in. The loader makes cleaning the chicken house a much easier chore, especially because I was using a shovel and wheelbarrow before. The loader has more power and lifting capacity than what I expected from a tractor this size. I have had zero issues so far, but have only had it for 3 months and only put 30 hours on it, so I will have to see on the quality. I plan on following all the recommended maintenance, and keep it as clean as possible, so i don't foresee and issues. One thing I would suggest to any potential buyers would be to shop around at different Deere dealers if possible. There are two different ones in my area, and the one I bought from quoted me $1700 cheaper than the other dealer with all the same equipment and set up.
greenthumbacres
- From: North Carolina, USA
- Usage Frequency: Daily
- Level of Experience: Intermediate
1025r Great Potential Poor Execution
So I will begin with that i started out with a x738. It was a great machine until the engine block was cracked at 365 hrs., and that was that. So my dealer said that the 1025r was a better more durable machine so I bought it and within the first 15hrs of use the machine had a coolant leak. So brought it back and the dealer fixed the hose fitting, because it was cracked. The next problem happened at 20 hours when I was mowing and the PTO shaft for the mower deck sheared at the u-joint. Note I was on level ground and it was brand new. Took it back to the dealer, and they fixed it in about 4 days. The next break down happened when the tractor wouldn't start. Turns out the power source to the starter wasn't connected very well and needed a new harness. At this point I was mad at the quality of the machine I spent over $27,000 on this machine and it keeps on breaking down while under warranty. The dealership is fixing it every time and thats fine. But if the machine breaks down again I might pull the plug, and trade to a 2038 or try and get a new one because this one isn't working out again. Rant Over Other wise its a great machine and the dealership is great with helping out
BobbyADA
- From: Southington, CT, USA
- Usage Frequency: Daily
- Level of Experience: Intermediate
1025R MAUSER CAB
JUST PURCHASED///IT DOES FIT UNDER A 7 FOOT GARAGE DOOR!!...IT IS VERY WELL CONSTRUCTED...I LIKE THE UPDATES FROM MY 2014 1025R VERY STABLE HIGHLY RECOMMEND ALONG WITH MY DEALER VALLEY PLAINS EQUIPMENT JAMESTOWN ND
MO73
- From: JAMESTOWN ND
- Usage Frequency: Weekly
- Level of Experience: Intermediate
Excellent subcompact tractor
Took delivery a few weeks ago. This SCUT is a work horse, love the four wheel drive and Yanmar Diesel engine which sips fuel. Got the imatch implement quick attach system, perfect. Also added the MCS20 or material collection system- I highly reccomend this if you want a top shelf bagging system for leaves and grass clipppings. The front end loader or FEL is powerful for such a small tractor. No tiller needed with an FEL and the Piranah tooth bar which I added after purchase. I went with the 54” deck which cuts my centipede grass nicely. You can also add a backhoe later on which is a nice option. You won’t regret this purchase.
Patriot1
- From: Shelby, NC, USA
- Usage Frequency: Weekly
- Level of Experience: Intermediate
fieldturf
Been doing research on this machine for several months and can't get over that RIO switch. I'll just stay with my old 25 year tractor or upgrade to a larger tractor. Can't believe I got to hold a switch to keep my PTO running when I back up. Wow
fieldturf
We Love Our 1025R
We love our NEW 1025R. It's our second. First 2014 1025R with front mount snowblower plus a Curtis Cab--No Good was cold, poor construction had diesel fumes, snow, water and noisy in cab. Now our 2017 1025R with front mounted snowblower plus NEW MAUSER CAB as seen in brochure excellent; warmer, quieter. OUR SALESMAN WAS RICK MARTIN @ THERIAULT EQUIPMENT in Presque Isle, ME. So stop by and get your own today. Don't wait financing available. Nothing Runs Like a Deere! And Also Nothing Blows Snow Like a Deere!!! You can quote me on that. We also own 2-X390 Lawn Tractors also excellant. Tell Rick Martin that Tom Gagnon sent you.
tomg
- From: St David, Madawaska, ME 04773, USA
- Usage Frequency: Weekly
- Level of Experience: Intermediate
Very good, thought out designed tractor.
I picked up my 1025r on October 27th 2015 and have put on twenty two hours so far. It's been a great tractor on my 4.6 acres of land. I was able to get the Frontier York rake with the 0% down promotion for free. I have the H120 loader as well. I was able to find the rest of my attachments (60" finish mower, 60" three point blade, and a set of quick attach forks) for under $1000.00. Why buy new implements when you can find good used stuff for a lot less and save money. These implements make this great Deere tractor more versatile. The tractor is good on fuel, and very comfortable. I'm 6'2" and can ride hours in great comfort. It's easy to run, and simple to service. Only trouble I had was a small hydraulic leak on one of the female couplings from the tractor to the loader(dealer fixed right off) and a very small coolant leak which I fixed my self by tighning a clamp. I highly recommend this tractor over any other brand and I did my research.
ShWheel79
- From: Vermont, USA
- Usage Frequency: Weekly
- Level of Experience: Expert
Great value and versatility
I recently purchased a 1025R and have to say I'm very impressed with what it can do. I have about three acres with much of it wooded and wanted a tractor to move dirt, clean up fallen trees, etc.. I've had it a week and already have more than 10 hours on it, and it's the middle of December. I'm not a contractor - this purchase was entirely for working my own property. Considering this is a relatively small tractor, the amount of power and versatility it delivers is amazing. I would have to say it's more than what I expected, and I'm more than pleased with the value.
gsaisselin
- From: Hartford, CT, USA
- Usage Frequency: Daily
- Level of Experience: Intermediate
1025R
I just purchased this new 1025R tractor with backhoe, loader bucket, and drive on mower. I love the ease of removing backhoe and loader. It is much easier than the old Kubota that I had. Have yet to remove the mover, but I am looking forward to do this when required. Tractor preforms out do the old one I had so far. It is also a bit larger than the Kubota. The only drawback is getting used to the operating requirements, but that will come in time.
Malvin
- Usage Frequency: Weekly
- Level of Experience: Beginner
This little tractor always surprises
I have owned my 1025R since early 2014 and have had no issues with it at all. It always surprises me at it's abilities and how much work it can do in a day. I have the H120 loader with a 5' bucket and pallet forks, post hole auger, 5' rotovator, 5' snowblower 4' rotary mower and a 6' rear mount finishing mower. It handles all of my implements extremely well and I couldn't be happier with my purchase. I have logged over 200 hours on the meter so far with no issues at all other than regular maintenance.
Sporty04
- From: Manitoba Canada
- Usage Frequency: Daily
- Level of Experience: Expert
she thinks my tractor's sexy
Purchased this for 5 acres of mowing and has done a great job, only complaint is where the rear lights are mounted. Mowing along a hedgerow the lights sometimes get hung up on a branch or shrubs and has broken away from ROV bar. Have them wired tied now to bar. Bucket has been an awesome attachment for moving stone, mulch and even snow. Have a blade that attaches to rear (given to me by my brother) that I also use for plowing snow. All in all, I Love my John Deere 1025R. Before I purchased it my brother said," a tractor payment is better then a car payment." I agree.
BobH
- From: Lower Saucon Township, PA, USA
- Usage Frequency: Weekly
- Level of Experience: Intermediate
after looking at 7 differant brands went back to deere havent had any problems
don't look for something you wont be happy with, this does everything you will need to do
weezl
- From: mascotte flordia
- Usage Frequency: Daily
- Level of Experience: Expert
Very good entry level tractor
This is my second JD tractor over the past 15 years. The 2210 was my 1st and ran flawlessly for 12 years and I got a good trade in price for it. My 1025r has loader, mower and backhoe. Runs very well after 3 years of regular use. The loader and backhoe are very well made, easy to remove and install. Not a fan of where the light switch is located, I hit my knee on it all the time. A bit to much plastic instead of steel but by trucks like that now too. For the money you can't go wrong getting a 1025. It's a very good compact tractor. John Deere resale value beats everyone else if you look after it.
Caper
- From: Nova Scotia, Canada
- Usage Frequency: Weekly
- Level of Experience: Intermediate
Love my tractor size
love my tractor size and all that I have done with it I got the 1025r filb didn't know how much you could do with it my brother-in-law has a much bigger John Deere but still calls me to do the jobs he can't get his larger tractor into and the Backhoe is great for ditches and hole digging wish I had a ripper tooth and bucket thumb will get it down the road has enough power for what I do with it I have seizures so I wanted the seat safety switch which it has so if I try to leave the seat the tractor shuts down and the hydrostats that drive the machine if I take my foot off of the pedal it comes to a stop even on a hill so the 1025r filb fits me just fine it's a little work horse the only problem I had with it is the stabilizer would leak off if the tractor was running or not so when I done the first year service the guys at John Deere shop got it replaced for me and it was under warranty work at no cost to me and that fixed the problem the guys at my local John Deere dealer want me to be happy with my purchase so they go above and beyond to make that happen I think I will get many years out of my machine and it makes my life so much easier to complete my jobs will recommend this to all of my friends
BubbaBlack
- Usage Frequency: Weekly
- Level of Experience: Intermediate
Good Power
I have owned the 1025R for one month, and already used it to move and level 18 yards of dirt, as well as mow my yard. This tractor has plenty of power. After removing about half of the dirt, I decided to see if it would push the rest of the pile. With the tractor in 4WD and low range, I raised the RPMs all the way and locked the rear differential. The tractor pushed the pile around with authority. Definitely a good setup by JD.
JackofallTrad3s
- From: Seneca County, OH, USA
- Usage Frequency: Weekly
- Level of Experience: Intermediate
Great tractor.
I put a lot of thought and research into John Deere tractors. People said,"Oh don't get a small tractor. You won't be satisfied. WRONG! 1025R does it all. Love the loader. Mulch, stone, dirt, debris. I have a rake and a scraper blade. I have a set of pallet forks. Not the clamp on type, the ones where you remove the bucket. Couldn't live without them. Lastly, have a four foot bush hog. Does a great job. Really gets in tight spots. Also, have done 3 bush hog jobs. 2 of them needed 4wd from the start to get through low, wet areas. This tractor is great in my yard and doing work for others, doesn't tear up grass or make tracks. Want to get more attachments soon. Love the 1025r.
Kevin66
- From: Marion, Md.
- Usage Frequency: Weekly
- Level of Experience: Expert
Great little tractor
I purchased my 1025R December 2017 and have 77 hours on it already. I use it for my own property (3 acres) and it has made the impossible - possible. From grading soil, removing tree stumps, and hauling brush and debris, this tractor has not let me down in any way. Considering it is a small tractor, it has more than enough power to get just about any job done. It can get into tight areas where a larger machine wouldn't be able to. The backhoe has plenty of power, the loader seems to lift whatever I put in it without any trouble. I purchased my tractor in lieu of renting one. This tractor will pretty much pay for itself the first year.
woodsman
- From: Hartford, CT, USA
- Usage Frequency: Weekly
- Level of Experience: Intermediate
Great Tractor - It will continually amaze you what it can do
My 1025R is an amazing tractor. I absolutely love it. I got the 60" auto connect deck, 260B back hoe with thumb and the 120R loader. Everything has worked very well and has that feel of quality. I was worried this tractor was going to be too small. However after operating it I am shocked how capable it really is. I would buy this tractor again without thinking twice. I looked at all the other tractors out there, they are not as well rounded of a machine as this. When you buy a Deere you expect quality, a well engineered machine, easy to use attachments and a machine that just operates well. John Deere delivered and then some. Totally satisfied.
Ducky
- From: Southern Michigan
- Usage Frequency: Weekly
- Level of Experience: Expert
back hoe
I LOVE MY JOHN DEERE , IT IS FUN TO DRIVE AND A TOUGH ANIMAL!!! I have the heavier bucket and larger mowing deck. my next attachment will be the back hoe.
jetpilotman
- From: johnscreek georgia
- Usage Frequency: Monthly
- Level of Experience: Beginner
Mower connection is difficlut
I have owned this tractor for 2.5 years now. Overall I love the tractor. However, the E_Z connect drive over mower is very difficult to accomplish. Trying to get everything to line up by yourself is impossible. The locking rod that holds the mower to the unit on the backside is extremely difficult to lock in place. The loader hooks up easily and so does the snow blower.
Weekendwarrior
- From: Greenville, MI 48838, USA
- Usage Frequency: Weekly
- Level of Experience: Expert
